--- title: FabriCAM Software Reduce Corner Cutting Speed (Part 2) Step by Step Video Tutorial source_url: https://softwaretraining.co.za/fabricam-reduce-corner-cutting-speed source_ref: https://softwaretraining.co.za/fabricam-reduce-corner-cutting-speed fetched_at: 2026-08-15T21:41:50Z category: training pass: softwaretraining-fabricam-reduce-corner-cutting-speed related_urls: - https://softwaretraining.co.za/?p=27543 - https://softwaretraining.co.za/?p=27541 - https://softwaretraining.co.za/?p=27544 - https://softwaretraining.co.za/?p=27542 - https://softwaretraining.co.za/fabricam-reduce-corner-cutting-speed - https://softwaretraining.co.za/fabricam-add-cad-markings - https://softwaretraining.co.za/fabricam-adjusting-torch-height - https://softwaretraining.co.za/fabricam-art-parts-import - https://softwaretraining.co.za/fabricam-removing-parts-form-panel - https://softwaretraining.co.za/fabricam-cad-selecting-hotspots - https://softwaretraining.co.za/fabricam-art-part-collisions - https://softwaretraining.co.za/fabricam-pre-piercing-cutting - https://softwaretraining.co.za/fabricam-loop-cutting-clean-corners - https://softwaretraining.co.za/flexiprint-gradient-fill - https://softwaretraining.co.za/flexiprint-blending-modes - https://softwaretraining.co.za/flexiprint-additional-contour-cutting - https://softwaretraining.co.za/inkrip-align-design-elements - https://softwaretraining.co.za/inkrip-icc-profiles-manager - https://softwaretraining.co.za/topic/machine - https://softwaretraining.co.za/training-videos/plasma-cutter/fabricam notes: English how-to page (html lang en-ZA). Embedded MP4 / YouTube embed / cover still not mirrored. This is Advanced Machine Configuration Settings how-to Part 2 (Reduce Corner Cutting Speed / Machine Reduce Speed), not an INDEX. Distinct from already-ingested Mini-Series INDEX training/fabricam-advanced-machining.md (body Mini-Series is ?p=27541; pretty slug fabricam-advanced-machining is NOT printed on THIS page; already in KB; dest 22724 not touched; leftover INDEX / p27541 HTML not reused; not recrawled). Distinct from already-ingested Part 1 training/fabricam-add-cad-markings.md (body previous is ?p=27542 Machine CAD Markings; pretty slug printed on this URL avia prev as fabricam-add-cad-markings; already in KB; dest 27857 not touched; leftover Part 1 HTML not reused; not recrawled). Distinct from unused body next ?p=27544 Machine - Reduce Torch Height (pretty slug not printed on the body link; not invented; avia next pretty slug fabricam-adjusting-torch-height printed; not fetched). Distinct from unused avia next Part 3 fabricam-adjusting-torch-height (pretty slug printed; not invented; not fetched). Distinct from the completed Advanced CAM series (different mini-series; INDEX training/fabricam-advanced-cam.md dest 22378 and Parts 1-4 dests not touched; not recrawled). INDEX body named this PART 2 - Machine - Reduce Speed. Do not ingest Part 3 this pass. One page only. Live GET of pretty slug fabricam-reduce-corner-cutting-speed 200. WordPress id 27543. Not fabricam-advanced-machining / not WP 27541. Not fabricam-add-cad-markings / not WP 27542. Not fabricam-adjusting-torch-height / not ?p=27544. Not fabricam-advanced-cam / not WP 27506. --- # FabriCAM Software Reduce Corner Cutting Speed (Part 2) Step by Step Video Tutorial **Source:** [https://softwaretraining.co.za/fabricam-reduce-corner-cutting-speed](https://softwaretraining.co.za/fabricam-reduce-corner-cutting-speed) (canonical on this live HTML; live file `/workspace/fabricam-reduce-corner-cutting-speed-fresh.html`; html `lang="en-ZA"`; `og:locale` `en_US` (also `en_ZA`); schema `inLanguage` `en-ZA`; WP-Super-Cache stamp **2026-08-15 20:00:41**; live GET of pretty slug `fabricam-reduce-corner-cutting-speed` **200**; HTTP Date Sat, 15 Aug 2026 21:41:50 GMT). Fetched 2026-08-15T23:41:50 SAST. Published **8 May 2023** (`datetime` `2023-05-08T12:49:54+02:00` / article published time `2023-05-08T10:49:54+00:00`). Site modified **8 August 2026** UTC / **8 August 2026** SAST (`2026-08-08T05:57:01+00:00` / `og:updated_time` `2026-08-08T07:57:01+02:00`). WordPress post id **27543**. Also known as `https://softwaretraining.co.za/?p=27543` (shortlink / wp-json posts/27543 / postid-27543 / html_entry_id_27543 / post-entry-27543 on this URL; **not separately re-fetched**). Alternate long pretty slug `fabricam-software-reduce-corner-cutting-speed-part-2-step-by-step-video-tutorial` also printed on this URL (query_vars name; **not invented**; **not fetched**). Not WordPress id 27541 and not slug `fabricam-advanced-machining`. Not WordPress id 27542 and not slug `fabricam-add-cad-markings`. Not WordPress id 27544 and not slug `fabricam-adjusting-torch-height`. Not WordPress id 27506 and not slug `fabricam-advanced-cam`. Not WordPress id 27507 / 27508 / 27509 / 27510. Same page as unused body PART 2 – Machine – Reduce Speed `?p=27543` named on already-ingested INDEX (pretty slug was **not** printed on that INDEX body link; leftover INDEX avia next on Part 1 printed pretty slug `fabricam-reduce-corner-cutting-speed`; **not invented**) and unused avia next Part 2 named on already-ingested Part 1 (pretty slug `fabricam-reduce-corner-cutting-speed` **was** printed on that Part 1 avia-next chrome). **What this is:** One public English how-to page on **softwaretraining.co.za**, an AM.CO.ZA training-video project ([achievement.co.za directory](https://achievement.co.za/) describes SoftwareTraining as an AM.CO.ZA project of short problem-solving CNC software videos). **FabriCAM is AM software** (AM.CO.ZA Fabricam CAD&CAM Sheet Metal Cutting Software). This page is **Part 2** titled Reduce Corner Cutting Speed. **This is a part, not an INDEX.** Distinct from already-ingested Mini-Series INDEX `training/fabricam-advanced-machining.md` (source [https://softwaretraining.co.za/fabricam-advanced-machining](https://softwaretraining.co.za/fabricam-advanced-machining); body Mini-Series link on this URL is [https://softwaretraining.co.za/?p=27541](https://softwaretraining.co.za/?p=27541); pretty slug `fabricam-advanced-machining` is **not printed** on THIS page; already in KB from prior ingest; dest **22724** not touched; leftover INDEX / p27541 HTML **not reused**; **not recrawled**), from already-ingested Part 1 `training/fabricam-add-cad-markings.md` (source [https://softwaretraining.co.za/fabricam-add-cad-markings](https://softwaretraining.co.za/fabricam-add-cad-markings); body previous on this URL is [https://softwaretraining.co.za/?p=27542](https://softwaretraining.co.za/?p=27542) Machine – CAD Markings; pretty slug printed on this URL avia prev; already in KB; dest **27857** not touched; leftover Part 1 HTML **not reused**; **not recrawled**), from unused body next Machine – Reduce Torch Height at [https://softwaretraining.co.za/?p=27544](https://softwaretraining.co.za/?p=27544) (pretty slug **not printed** on the body link; **not invented**; avia next pretty slug [https://softwaretraining.co.za/fabricam-adjusting-torch-height](https://softwaretraining.co.za/fabricam-adjusting-torch-height) printed; **not fetched**), from unused avia next Part 3 [https://softwaretraining.co.za/fabricam-adjusting-torch-height](https://softwaretraining.co.za/fabricam-adjusting-torch-height) (title: "FabriCAM Software Adjusting Machine Torch Height (Part 3) Step by Step Video Tutorial"; pretty slug printed; **not invented**; **not fetched**), from already-ingested Advanced CAM INDEX `training/fabricam-advanced-cam.md` (source [https://softwaretraining.co.za/fabricam-advanced-cam](https://softwaretraining.co.za/fabricam-advanced-cam); already in KB; dest **22378** not touched; leftover Advanced CAM INDEX HTML **not reused**; **not recrawled**; **not printed as a body/avia link on this URL**), from already-ingested Advanced CAM Parts 1-4 `training/fabricam-lead-in-out-zero-away.md` / `training/fabricam-lead-length-percentage.md` / `training/fabricam-loop-cutting-clean-corners.md` / `training/fabricam-pre-piercing-cutting.md` (already in KB; dests **23823** / **25687** / **26260** / **29051** not touched; leftover Advanced CAM part HTML **not reused**; **not recrawled**; More Training Videos on this URL reprints already-ingested `fabricam-pre-piercing-cutting` and `fabricam-loop-cutting-clean-corners`; **not recrawled**), from unused You-might-also-like other FabriCAM / FlexiPRINT / InkRIP pages printed on this URL (cited not fetched except as already in KB), from unused More Training Videos InkRIP / FlexiPRINT / FabriCAM pages printed on this URL (cited not fetched except as already in KB), from unused More Articles AM promo / RSS chrome on this URL (cited not fetched; **buythis was not crawled**), from already-ingested YMAL `training/fabricam-art-parts-import.md` (pretty slug printed on this URL as [https://softwaretraining.co.za/fabricam-art-parts-import](https://softwaretraining.co.za/fabricam-art-parts-import); already in KB; **not recrawled**), from already-ingested YMAL `training/inkrip-align-design-elements.md` (pretty slug printed; already in KB; **not recrawled**), from already-ingested sidebar ICC INDEX `training/inkrip-icc-profiles-manager.md` (already in KB; **not recrawled**), from already-ingested CAD Basics INDEX + Parts 1-10, from already-ingested Import Tab INDEX + Parts 1-3, from already-ingested Secondary CAM Toolbar Practicals INDEX + Parts 1-3, from already-ingested Design Practices INDEX + Parts 1-5, from already-ingested Before Starting INDEX + Parts 1-2, from already-ingested Getting Started INDEX + Parts 1-5, from already-ingested Introduction INDEX + Parts 1-7, from already-ingested Job Manager INDEX + Parts 1-3, from already-ingested transform INDEX + Parts 1-8, from already-ingested toolbar INDEX + Parts 1-8, from already-ingested ICC INDEX + Parts 1-11, from already-ingested printer-drivers INDEX + Parts 1-8, from category summary `training/fabricam-training.md` (source [https://softwaretraining.co.za/training-videos/plasma-cutter/fabricam](https://softwaretraining.co.za/training-videos/plasma-cutter/fabricam)), and from `youtube/fabricam-howtos.md`. Named as unused body PART 2 `?p=27543` on already-ingested INDEX (pretty slug was **not** printed on that INDEX body link) and unused avia next Part 2 on already-ingested Part 1 (pretty slug `fabricam-reduce-corner-cutting-speed` **was** printed). **This does not continue the Advanced CAM Configuration Settings numbered series** (that INDEX and Parts 1-4 already complete; different mini-series). **This does not ingest Advanced Machine Configuration Settings Part 3 this pass.** **fabricam-adjusting-torch-height was not ingested this pass.** **Part 3 pretty slug was printed on this URL as avia next `fabricam-adjusting-torch-height`; not invented; not fetched.** **fabricam-add-cad-markings dest 27857 was not touched this pass.** **fabricam-advanced-machining dest 22724 was not touched this pass.** **fabricam-advanced-cam dest 22378 was not touched this pass.** **fabricam-pre-piercing-cutting dest 29051 was not touched this pass.** **fabricam-lead-in-out-zero-away dest 23823 was not touched this pass.** **fabricam-lead-length-percentage dest 25687 was not touched this pass.** **fabricam-loop-cutting-clean-corners dest 26260 was not touched this pass.** **Not FlexiPRINT / PrintEXP / UltraPrint / AcroRIP / InkRIP.** Distinct: InkRIP (AM software, different RIP programme; already-ingested YMAL `inkrip-align-design-elements` / sidebar ICC INDEX are chrome on this URL, not this FabriCAM how-to, and were not recrawled except as already in KB), PrintEXP (AM software, different RIP / control programme; not this FabriCAM how-to and not fetched), UltraPrint (not AM software), AcroRIP, WellPrintEXP (stored/OEM), FlexiPRINT / FlexiSTARTER (SAi third-party stored; You-might-also-like / More Training Videos / sidebar / category chrome on this URL names FlexiPRINT pages and folders; those are different pages, not this how-to, and were not fetched). Sidebar / category chrome on this URL names FlexiPRINT / other RIP / vinyl / laser / CorelDRAW / Photoshop training-video folders; those are different pages, not this how-to, and were not fetched. You-might-also-like also names FlexiPRINT / other FabriCAM / InkRIP pages (not this how-to; not fetched except as already in KB). Sidebar chrome on this URL also names buythis.co.za; **buythis was not crawled**. Sidebar chrome also names cncu.co.za; **cncu was not crawled**. Cover chrome names fabricam.co.za; **fabricam.co.za was not crawled**. Share-on-WhatsApp / share-by-mail are page chrome only; **email / WhatsApp were not crawled**. YouTube channel links are present in page chrome; **YouTube was not crawled**. Footer / More Websites chrome also names am.co.za / vinylcut.co.za / machining.co.za / cnctools.co.za / filaments.co.za / other AM sites; **those hosts were not crawled** except as already in KB. ## English peek (quoted from the live page) Quoted from [https://softwaretraining.co.za/fabricam-reduce-corner-cutting-speed](https://softwaretraining.co.za/fabricam-reduce-corner-cutting-speed): - Title: "FabriCAM Software Reduce Corner Cutting Speed (Part 2) Step by Step Video Tutorial" - Cover chrome: "fabricam reduce corner cutting speed" - "Now if you are looking at doing some more cleaner corner cutting, then adjusting the cutting speed will be of great help." - "This video is part of a Mini-Series that covers the Advanced Machine Configuration." - "Next video covers Machine – Reduce Torch Height." - "Previous video covered Machine – CAD Markings." - Category: Training Videos - Tags: AM.CO.ZA, FabriCAM, FabriCAM CAD&CAM, Machine - Date on page: 8 May 2023 English confirmation: `html lang="en-ZA"`, `og:locale` `en_US` / `en_ZA`, schema `inLanguage` `en-ZA`, prose above is English. ## How to reduce corner cutting speed in FabriCAM (from this page) The live page body is short; the on-page "Video Transcript" block is the step source. **Raw auto-caption is not copied in full; no transcript invented.** Cleaned steps from that live block: 1. This Advanced Machine Configuration Settings part is about **reducing torch / cutting speed at corners**. 2. The live block starts from a basic sheet-metal sheet with a square that will be cut. 3. With the setting on, when the cut gets close to a corner it **slows down**, finishes the corner, then **speeds up** again. 4. That is meant to give a clearer finish and less messy corners. 5. In FabriCAM, open **Configuration → Machines** (the live block calls this the third tab) and open the **cutting technology table** at the bottom. 6. Activate **reduced speed in vertices**. The live block shows default **speed 75%**, **distance before vertices** three mil, and **distance after** three mil (then it speeds up again). 7. Apply and OK. Keep in mind the setting is on: if corners later misbehave, check whether this setting is still active. 8. Recap closer also names the next part (torch height; the live block says the two often go hand in hand) and [https://softwaretraining.co.za/](https://softwaretraining.co.za/) search (top right). ## Mini-series context (cited, not recrawled as extra pages) From the same page (body + prev/next chrome on this URL): - Mini-series INDEX named on this page (body Mini-Series link): WordPress id `27541` at [https://softwaretraining.co.za/?p=27541](https://softwaretraining.co.za/?p=27541) (pretty slug already in KB as [https://softwaretraining.co.za/fabricam-advanced-machining](https://softwaretraining.co.za/fabricam-advanced-machining) from prior ingest; **not printed** on THIS page; already in KB as `training/fabricam-advanced-machining.md`; dest **22724** not touched; leftover INDEX / p27541 HTML **not reused**; **not recrawled** this pass). Pretty slug `fabricam-advanced-machining` was **not** reprinted as a body Mini-Series href on this URL (body Mini-Series is `?p=27541`; **not invented**). Avia prev chrome on this URL is Part 1, not the INDEX. - Previous named in the body on this page: Machine – CAD Markings at [https://softwaretraining.co.za/?p=27542](https://softwaretraining.co.za/?p=27542) (pretty slug printed on this URL avia prev as [https://softwaretraining.co.za/fabricam-add-cad-markings](https://softwaretraining.co.za/fabricam-add-cad-markings); already in KB as `training/fabricam-add-cad-markings.md`; dest **27857** not touched; leftover Part 1 HTML **not reused**; **not recrawled** this pass). - Next named in the body on this page: Machine – Reduce Torch Height at [https://softwaretraining.co.za/?p=27544](https://softwaretraining.co.za/?p=27544) (pretty slug **not printed** on the body link; **not invented**; avia next pretty slug [https://softwaretraining.co.za/fabricam-adjusting-torch-height](https://softwaretraining.co.za/fabricam-adjusting-torch-height); **not fetched** this pass). - Avia prev chrome on this URL: FabriCAM Software Adding Auto Cad Markings in the Design (Part 1) Step by Step Video Tutorial at [https://softwaretraining.co.za/fabricam-add-cad-markings](https://softwaretraining.co.za/fabricam-add-cad-markings) (pretty slug printed; already in KB; dest **27857** not touched; **not recrawled** this pass). - Avia next chrome on this URL: FabriCAM Software Adjusting Machine Torch Height (Part 3) Step by Step Video Tutorial at [https://softwaretraining.co.za/fabricam-adjusting-torch-height](https://softwaretraining.co.za/fabricam-adjusting-torch-height) (pretty slug printed; **not invented**; **not fetched** this pass). - Related chrome on this URL also names already-ingested sidebar ICC INDEX [https://softwaretraining.co.za/inkrip-icc-profiles-manager](https://softwaretraining.co.za/inkrip-icc-profiles-manager) (`training/inkrip-icc-profiles-manager.md`; **not recrawled**). **Next unused part printed on this URL:** avia next [https://softwaretraining.co.za/fabricam-adjusting-torch-height](https://softwaretraining.co.za/fabricam-adjusting-torch-height) pretty slug printed (FabriCAM Software Adjusting Machine Torch Height Part 3). Body next `?p=27544` pretty slug **not printed**; **not invented**. Avia prev [https://softwaretraining.co.za/fabricam-add-cad-markings](https://softwaretraining.co.za/fabricam-add-cad-markings) is already in KB. Body previous `?p=27542` is already in KB (dest 27857 not touched). Body Mini-Series `?p=27541` is already in KB (dest 22724 not touched). **fabricam-adjusting-torch-height was not ingested this pass.** ## Related chrome on the same URL (cited, not re-fetched) More Articles / You-might-also-like / More Training Videos / related chrome on this URL also names other pages. **Not fetched this pass** except as already in KB: Already in KB: - [https://softwaretraining.co.za/?p=27541](https://softwaretraining.co.za/?p=27541) (body Mini-Series; pretty slug already in KB as `fabricam-advanced-machining` from prior ingest; **not printed** on THIS page) - `training/fabricam-advanced-machining.md` (dest **22724** not touched) - [https://softwaretraining.co.za/?p=27542](https://softwaretraining.co.za/?p=27542) (body previous; "Machine – CAD Markings") - pretty slug printed on this URL avia prev - [https://softwaretraining.co.za/fabricam-add-cad-markings](https://softwaretraining.co.za/fabricam-add-cad-markings) (avia prev; "FabriCAM Software Adding Auto Cad Markings in the Design (Part 1) Step by Step Video Tutorial") - `training/fabricam-add-cad-markings.md` (dest **27857** not touched) - [https://softwaretraining.co.za/fabricam-art-parts-import](https://softwaretraining.co.za/fabricam-art-parts-import) (YMAL; "FabriCAM Software Art Parts Configuration Import (Part 2) Step by Step Video Tutorial") - [https://softwaretraining.co.za/inkrip-align-design-elements](https://softwaretraining.co.za/inkrip-align-design-elements) (YMAL; "How to Align Multiple Designs Elements Within the AM.CO.ZA InkRIP Software (Part 4)") - [https://softwaretraining.co.za/fabricam-pre-piercing-cutting](https://softwaretraining.co.za/fabricam-pre-piercing-cutting) (More Training Videos; "FabriCAM Software CAM Pre-Piercing for Cutting (Part 4) Step by Step Video Tutorial") - `training/fabricam-pre-piercing-cutting.md` (dest **29051** not touched) - [https://softwaretraining.co.za/fabricam-loop-cutting-clean-corners](https://softwaretraining.co.za/fabricam-loop-cutting-clean-corners) (More Training Videos; "FabriCAM Software Loop Cutting Clean Corners (Part 3) Step by Step Video Tutorial") - `training/fabricam-loop-cutting-clean-corners.md` (dest **26260** not touched) - [https://softwaretraining.co.za/inkrip-icc-profiles-manager](https://softwaretraining.co.za/inkrip-icc-profiles-manager) (sidebar ICC INDEX) - `training/inkrip-icc-profiles-manager.md` Not in KB (hotlinked only; pretty slugs printed on this URL unless noted): - [https://softwaretraining.co.za/?p=27544](https://softwaretraining.co.za/?p=27544) (body next; "Machine – Reduce Torch Height"; pretty slug **not printed** on the body link; **not invented**) - [https://softwaretraining.co.za/fabricam-adjusting-torch-height](https://softwaretraining.co.za/fabricam-adjusting-torch-height) (avia next; "FabriCAM Software Adjusting Machine Torch Height (Part 3) Step by Step Video Tutorial"; pretty slug printed) - [https://softwaretraining.co.za/fabricam-removing-parts-form-panel](https://softwaretraining.co.za/fabricam-removing-parts-form-panel) (YMAL; "FabriCAM Software Removing Parts form Panel List (Part 3) Step by Step Video Tutorial") - [https://softwaretraining.co.za/fabricam-cad-selecting-hotspots](https://softwaretraining.co.za/fabricam-cad-selecting-hotspots) (YMAL; "FabriCAM Software Selecting Hotspots in the CAD Feature (Part 4) Step by Step Video Tutorial") - [https://softwaretraining.co.za/fabricam-art-part-collisions](https://softwaretraining.co.za/fabricam-art-part-collisions) (More Training Videos; "FabriCAM Software Detailed Vector Art Part Collisions (Part 3) Step by Step Video Tutorial") - [https://softwaretraining.co.za/flexiprint-gradient-fill](https://softwaretraining.co.za/flexiprint-gradient-fill) (YMAL; "Understanding the Gradient Fill within the SAi FlexiPRINT RTUV 22 Software (Part 3)") - [https://softwaretraining.co.za/flexiprint-blending-modes](https://softwaretraining.co.za/flexiprint-blending-modes) (YMAL; "Having a Look at the Blending Modes within the SAi FlexiPRINT RTUV 22 Software (Part 6)") - [https://softwaretraining.co.za/flexiprint-additional-contour-cutting](https://softwaretraining.co.za/flexiprint-additional-contour-cutting) (More Training Videos; "Additional Contour Cutting Options within the SAi FlexiPRINT RTUV 22 Software (Part 2)") - [https://softwaretraining.co.za/the-general-preferences-part-one-with-the-sai-flexiprint-rtuv-22-software-part-1](https://softwaretraining.co.za/the-general-preferences-part-one-with-the-sai-flexiprint-rtuv-22-software-part-1) (More Training Videos; long pretty slug printed) - [https://softwaretraining.co.za/additional-contour-cutting-options-within-the-sai-flexiprint-rtuv-22-software-part-2](https://softwaretraining.co.za/additional-contour-cutting-options-within-the-sai-flexiprint-rtuv-22-software-part-2) (More Training Videos; long pretty slug printed) - [https://softwaretraining.co.za/setting-up-different-contour-cuts-within-the-sai-flexiprint-rtuv-22-software-part-7](https://softwaretraining.co.za/setting-up-different-contour-cuts-within-the-sai-flexiprint-rtuv-22-software-part-7) (More Training Videos; long pretty slug printed) - [https://softwaretraining.co.za/using-the-copy-cut-and-paste-within-the-sai-flexiprint-rtuv-22-software-part-4](https://softwaretraining.co.za/using-the-copy-cut-and-paste-within-the-sai-flexiprint-rtuv-22-software-part-4) (More Training Videos; long pretty slug printed) - [https://softwaretraining.co.za/topic/machine](https://softwaretraining.co.za/topic/machine) (tag chrome; pretty slug printed) Off-series chrome on this URL (not fetched): You-might-also-like other FabriCAM / FlexiPRINT / InkRIP pages above; More Articles AM promo / RSS chrome (buythis not crawled); More Training Videos long pretty slugs including FlexiPRINT; sidebar ICC INDEX already in KB. Body Mini-Series `?p=27541` is already in KB (dest 22724 not touched; pretty slug not printed on THIS page). Avia prev `fabricam-add-cad-markings` already in KB (dest 27857 not touched). Avia next `fabricam-adjusting-torch-height` unused (pretty slug printed; not invented; not fetched). Body next `?p=27544` unused (pretty slug not printed; not invented; not fetched). Body previous `?p=27542` already in KB. Alternate long pretty slug also printed on this URL for this Part 2 itself (`fabricam-software-reduce-corner-cutting-speed-part-2-step-by-step-video-tutorial`); **not invented; not fetched**. More Training Videos also reprints long pretty slugs for FlexiPRINT pages above; **not invented; not fetched**. ## Embedded video (not mirrored) The page embeds a self-hosted MP4: [https://stfile.s3.eu-west-1.amazonaws.com/27543.mp4](https://stfile.s3.eu-west-1.amazonaws.com/27543.mp4) (poster [https://stfile.s3.eu-west-1.amazonaws.com/27543-thumbnail.jpg](https://stfile.s3.eu-west-1.amazonaws.com/27543-thumbnail.jpg)). Featured still: [https://softwaretraining.co.za/wp-content/uploads/2023/06/27543-featured-image.jpg](https://softwaretraining.co.za/wp-content/uploads/2023/06/27543-featured-image.jpg). **Not downloaded.** A YouTube embed is also present on this URL (embed id `UL7uoFFF75g`); **not crawled; not mirrored.** The page includes an on-page "Video Transcript" block; **not copied in full; no transcript invented.** Frame stills on this URL include [https://stfile.s3.eu-west-1.amazonaws.com/27543-frame.jpg](https://stfile.s3.eu-west-1.amazonaws.com/27543-frame.jpg) through `27543-frame9.jpg` and the YouTube embed for `UL7uoFFF75g`; **not downloaded**. ## Training phones (page chrome on the same URL) From [https://softwaretraining.co.za/fabricam-reduce-corner-cutting-speed](https://softwaretraining.co.za/fabricam-reduce-corner-cutting-speed) header: - Sales: 072 222 2211 - Support: 076 666 6655 - Training: 060 818 1818 - Jo'burg: 087 802 5368 - Cape Town: 087 802 7106 ## Skipped this pass - Unused avia next / body next Part 3 `fabricam-adjusting-torch-height` / `?p=27544` (avia next pretty slug printed; body next pretty slug not printed; not invented; not fetched) - Already-ingested Mini-Series INDEX `training/fabricam-advanced-machining.md` (already in KB; dest 22724 not touched; leftover INDEX HTML not reused; not recrawled; pretty slug not printed on THIS page) - Already-ingested Part 1 `training/fabricam-add-cad-markings.md` (already in KB; dest 27857 not touched; leftover Part 1 HTML not reused; not recrawled) - Already-ingested Advanced CAM INDEX `training/fabricam-advanced-cam.md` (already in KB; dest 22378 not touched; leftover INDEX HTML not reused; not recrawled) - Already-ingested Advanced CAM Parts 1-4 `training/fabricam-lead-in-out-zero-away.md` / `training/fabricam-lead-length-percentage.md` / `training/fabricam-loop-cutting-clean-corners.md` / `training/fabricam-pre-piercing-cutting.md` (already in KB; dests 23823 / 25687 / 26260 / 29051 not touched; leftover part HTML not reused; not recrawled) - You-might-also-like `fabricam-removing-parts-form-panel` / `fabricam-cad-selecting-hotspots` / `flexiprint-gradient-fill` / `flexiprint-blending-modes` (pretty slugs printed; not fetched except as already in KB for `fabricam-art-parts-import` / `inkrip-align-design-elements`) - More Training Videos `fabricam-art-part-collisions` / FlexiPRINT long pretty slugs (pretty slugs printed; not fetched except as already in KB for `fabricam-pre-piercing-cutting` / `fabricam-loop-cutting-clean-corners`) - More Articles AM promo / RSS chrome (not fetched; buythis not crawled) - Sidebar ICC INDEX `training/inkrip-icc-profiles-manager.md` (already in KB; not recrawled) - Already-ingested CAD Basics INDEX + Parts 1-10 (already in KB; not recrawled) - Already-ingested Import Tab INDEX + Parts 1-3 (already in KB; not recrawled) - Already-ingested Secondary CAM Toolbar Practicals INDEX + Parts 1-3 (already in KB; not recrawled) - Design Practices INDEX + Parts 1-5 (already in KB; not recrawled) - Before Starting INDEX + Parts 1-2 (already in KB; not recrawled) - Getting Started INDEX + Parts 1-5 (already in KB; not recrawled) - Introduction INDEX + Parts 1-7 (already in KB; not recrawled) - Job Manager INDEX + Parts 1-3 (already in KB; not recrawled) - Transform INDEX + Parts 1-8 (already in KB; not recrawled) - Toolbar INDEX + Parts 1-8 (already in KB; not recrawled) - ICC INDEX + Parts 1-11 (already in KB; not recrawled) - Printer-drivers INDEX and Parts 1-8 (already in KB; not recrawled) - Cover / frame still binaries / MP4 / YouTube embed - dump refresh skipped - Graphtec redo skipped - Firmware quiet (existing InkRIP / PrintEXP firmware indexes not rewritten)